Model: AM-64BT
UHF RFID reader module AM-64BT
$53.00
暂无数据
Shipping cost within 10kg is $100, and for every additional 1kg, the shipping cost increases by $5
Description
The radio frequency is based on the domestic Zhikun IBAT2000 dedicated UHF RFID chip design;
Fully supports ISO-18000-6C (EPC G2) protocol standards;
Working frequency 865-868MHZ, 902-928MHZ (can be adjusted according to the requirements of different countries or regions);
The serial port-based command system is concise, efficient, convenient and fast to integrate.
Detail
|
Purchase code (product model) |
AM-64BT |
|
|
Physical parameters |
||
|
Length (PCB length) mm |
67.8mm |
|
|
Length (including RF connector) mm |
77.0mm |
|
|
Width mm |
51.5mm |
|
|
Height (mm) |
9mm |
|
|
Operating temperature |
-20°C – + 70 °C |
|
|
Storage temperature |
-20°C – +85°C |
|
|
Operating humidity |
< 95% ( + 25 °C) |
|
|
Antenna interface |
||
|
SMA Connectors |
4-way SMA female antenna interface |
|
|
Electrical parameters |
||
|
Air interface protocol |
EPCglobal UHF Class 1 Gen 2 / ISO 18000-6C |
|
|
Work area support |
The United States, Canada and other regions that meet the US FCC certification standards EU and other regions compliant with ETSI EN 302 208 Mainland China, Japan, South Korea, Malaysia, Taiwan |
|
|
Working Mode |
Fixed frequency/Frequency hopping |
|
|
Card reading power consumption |
10W(33dBm) |
|
|
Working frequency band |
86 5~928 MHz |
|
|
Operating voltage |
DC 4.5V~5.5V |
|
|
Working current |
300mA~2.5A |
|
|
Standby current |
<50mA (EN pin high level) |
|
|
Maximum output power |
10 - 33dBm |
|
|
Output power accuracy |
1dBm |
|
|
GPIO |
2-way input, 2-way output |
|
|
Communication baud rate |
115200 bps (default and recommended) 38400 bps |
|
|
Inventory label speed |
＞ 500pcs /S |
|
|
Receiving sensitivity |
＜- 74 dBm |
|
|
Communication interface |
Uart (3.3V TTL) |
|
|
Antenna connection protection |
support |
|
|
Label RSSI |
support |
|
|
Antenna impedance matching measurement |
support |
|
|
EAS Function |
support |
|
|
Ambient temperature measurement |
support |
|
|
Label RSSI |
support |
|
|
15P Connector PIN Definition |
||
|
Connector Model: Molex 53261-1571 |
||
|
PIN |
definition |
illustrate |
|
1 |
GND |
Logically |
|
2 |
GND |
|
|
3 |
DC4.5V`DC5.5V |
Connect power supply at the same time |
|
4 |
DC4.5V`DC5.5V |
|
|
5 |
GPIO 1 |
General IO port |
|
6 |
GPIO 2 |
General IO port |
|
7 |
GPIO 3 |
General IO port |
|
8 |
buzzer |
Driven (can be directly connected to 3.3V active buzzer) |
|
9 |
UART_RXD |
Serial port RX, TTL 3.3V |
|
10 |
UART_TXD |
Serial port TX, TTL 3.3V |
|
11 |
SWDIO |
JINK - interface for debugging data input |
|
12 |
SWCLK |
JINK - debug basic clock signals |
|
13 |
GPIO 4 |
General IO port |
|
14 |
EN |
Module enable pin DC3.3V-5V |
|
15 |
GPIO 5 |
General IO port |
|
Notice: |
1. When the ambient temperature measurement function measures a temperature exceeding 60°, it is not suitable to work at full load; 2. Please install the heat sink in time when working continuously at full load; 3. The power supply voltage cannot exceed 5V, otherwise it will cause circuit damage; 4. Be cautious when the RF output power is greater than 30dbm, as the peak current and temperature rise will increase significantly |
|